Electricity explains what electric current is, what drives it, and what resists it. It builds from current and potential difference to Ohm’s law, then to resistance and resistivity, series and parallel combinations, the heating effect of current, and electric power and energy. It is the numerical heart of the Class 10 physics section: almost every board paper carries a resistivity or combination calculation, a circuit diagram, and a question on why homes are wired in parallel or why nichrome heats and tungsten glows.
Key Concepts
1. Electric Charge and Electric Current
Think of a water pipe. Water flowing past a point every second is the flow rate; charge flowing past a point in a wire every second is the electric current. Current is the rate of flow of electric charge through a cross-section of a conductor.
I = Q / t
- I = electric current, unit ampere (A)
- Q = charge that crosses the section, unit coulomb (C)
- t = time taken, unit second (s)
One ampere is the current when one coulomb of charge flows through a section of the conductor in one second.
In metals the moving charges are free electrons; insulators have none, so no current flows through them.
Direction of current: by convention, current flows from the positive terminal of a cell to the negative terminal through the outer circuit. Electrons, being negatively charged, move the opposite way, from the negative terminal to the positive terminal.
An electric circuit is a continuous, closed path along which current can flow. Open the switch (plug key) anywhere in the loop and the current stops everywhere in that loop.
Ammeter: the instrument that measures current. It is connected in series with the component so that the whole current passes through it, and it has a very low resistance so that it changes the circuit current as little as possible. Its positive terminal goes towards the positive terminal of the battery.
2. Electric Potential and Potential Difference
Water flows in a pipe only when there is a pressure difference between its ends. Charge flows in a conductor only when there is a difference in electric potential between its ends. A cell or battery creates and maintains that difference using the chemical reaction inside it.
The potential difference between two points is the work done to move a unit positive charge from one point to the other.
V = W / Q
- V = potential difference, unit volt (V)
- W = work done, unit joule (J)
- Q = charge moved, unit coulomb (C)
One volt is the potential difference between two points when 1 joule of work is done to move a charge of 1 coulomb from one point to the other. So 1 V = 1 J/C. This is a 1-mark definition that CBSE has asked directly; write both the sentence and the relation.
Voltmeter: the instrument that measures potential difference. It is connected in parallel across the two points, and it has a very high resistance so that it draws almost no current from the circuit.
3. Ohm’s Law
For a metallic wire at steady temperature, doubling the potential difference doubles the current, tripling it triples the current, and so on. The current through a conductor is directly proportional to the potential difference across its ends, provided the temperature and other physical conditions stay the same.
V ∝ I, therefore V = I R, or V / I = R (a constant for the conductor)
R is the resistance of the conductor. The proportionality holds only when temperature is constant; if the wire heats up, its resistance rises and the ratio V/I changes. State the condition every time you state the law, otherwise the answer is incomplete.
The V-I Graph
For a conductor that obeys Ohm’s law (an ohmic conductor, such as a nichrome or copper wire at steady temperature), a graph of V on the y-axis against I on the x-axis is a straight line through the origin. The slope of this V-I line equals the resistance R. If I is plotted on the y-axis against V, the slope equals 1/R.
Two wires on the same V-I graph: the steeper line (larger V for the same I) has the larger resistance. Board questions have asked which of two straight lines belongs to a series combination and which to a parallel combination of the same two resistors; the steeper V-I line is the series combination because its resistance is larger.
A filament bulb is a non-ohmic device: as the filament gets hot its resistance increases, so the V-I graph curves away from a straight line.
Verification (NCERT Activity): connect a nichrome wire, an ammeter, a plug key and one cell in series, with a voltmeter across the wire. Note V and I, then repeat with two, three and four cells. V/I comes out nearly constant, and the V-I plot is a straight line through the origin. In a 5-mark question the circuit diagram carries its own marks: one loop for battery, key, ammeter and wire, with the voltmeter as a side branch across the wire only.
4. Resistance and Resistivity
Resistance is the property of a conductor that opposes the flow of charge through it. Free electrons drifting through a metal keep colliding with the fixed atoms of the metal, and these collisions slow the flow. Resistance is measured in ohm (Ω).
R = V / I
One ohm is the resistance of a conductor when a potential difference of 1 volt across its ends drives a current of 1 ampere through it. So 1 Ω = 1 V/A.
Factors on Which Resistance Depends
NCERT Activity 11.3 uses a cell, an ammeter and different nichrome wires. Doubling the length halves the current; using a thicker wire of the same length and material increases the current; replacing nichrome with copper of the same size increases the current a great deal. From this:
- Resistance is directly proportional to length: R ∝ l
- Resistance is inversely proportional to the area of cross-section: R ∝ 1/A
- Resistance depends on the nature of the material
- Resistance increases with temperature for metals
Combining the first three:
R = ρ l / A
ρ (rho) is the electrical resistivity of the material. Rearranging, ρ = R A / l, so its SI unit is Ω m2 / m = Ω m (ohm metre). CBSE 2025 asked exactly this derivation of the unit for 3 marks, together with the reason alloys are used in heating devices.
Resistivity is a property of the material, so two copper wires of different lengths and thicknesses have the same resistivity and different resistances.
Resistivity Values (NCERT Table 11.2, at 20 °C)
| Class | Material | Resistivity (Ω m) | Use or remark |
|---|---|---|---|
| Conductors | Silver | 1.60 × 10-8 | Best conductor; too costly for wiring |
| Copper | 1.62 × 10-8 | Electrical wires, cables | |
| Aluminium | 2.63 × 10-8 | Overhead transmission lines | |
| Tungsten | 5.20 × 10-8 | Bulb filaments | |
| Iron | 10.0 × 10-8 | - | |
| Alloys | Constantan (Cu + Ni) | 49 × 10-6 | Standard resistance coils |
| Manganin (Cu + Mn + Ni) | 44 × 10-6 | Standard resistances | |
| Nichrome (Ni + Cr + Mn + Fe) | 100 × 10-6 | Heating elements | |
| Insulators | Glass | 1010 to 1014 | - |
| Hard rubber | 1013 to 1016 | Insulation on wires |
Three facts to pull from this table: metals and alloys have resistivity of the order 10-8 to 10-6 Ω m and are good conductors; insulators are 1012 to 1017 Ω m; and alloys have higher resistivity than their constituent metals. Alloys also oxidise (burn) less readily at high temperature, which is why nichrome is used in toasters, irons and heaters while pure copper is used for connecting wires.
Stretching, Cutting and Bending a Wire
Stretching: volume stays constant. If a wire is stretched to n times its length, its area becomes A/n, so the new resistance is n2 times the old. Doubling the length by stretching makes the resistance 4 times; tripling makes it 9 times.
Cutting: each of n equal pieces has resistance R/n. If the n pieces are then joined in parallel, the combination has resistance (R/n)/n = R/n2. CBSE 2025 asked this for three pieces (answer R/9); the NCERT exercise asks it for five pieces (ratio R/R’ = 25).
Bending: coiling a wire changes neither its length, its area nor its material, so the resistance is unchanged. CBSE 2025 tested this as an assertion-reason item.
Doubling the diameter: area depends on the square of the radius, so doubling the diameter makes the area 4 times and the resistance one-fourth.
5. Resistance of a System of Resistors
a) Resistors in Series
Resistors joined end to end so that the same current passes through each are in series. Let R1, R2, R3 be in series across a battery of potential difference V, and let the current be I. The potential differences across the three are V1 = I R1, V2 = I R2, V3 = I R3. Since the total potential difference is shared,
V = V1 + V2 + V3
If Rs is the single resistor that would draw the same current I from the same battery, V = I Rs. So
I Rs = I R1 + I R2 + I R3, giving Rs = R1 + R2 + R3
- Same current through every resistor
- Potential difference divides in proportion to resistance (bigger R gets bigger V)
- Equivalent resistance is larger than the largest single resistance
- If one resistor burns out, the whole circuit is dead (this is why old fairy-light strings went dark when one bulb failed)
b) Resistors in Parallel
Resistors joined between the same two points, so that each has the same potential difference across it, are in parallel. Let R1, R2, R3 be in parallel across V. The currents through them are I1 = V/R1, I2 = V/R2, I3 = V/R3. The total current drawn from the battery is
I = I1 + I2 + I3
If Rp is the equivalent single resistor, I = V/Rp. So
V/Rp = V/R1 + V/R2 + V/R3, giving 1/Rp = 1/R1 + 1/R2 + 1/R3
- Same potential difference across every resistor
- Current divides in inverse proportion to resistance (smaller R takes more current)
- Equivalent resistance is smaller than the smallest single resistance
- Each branch works on its own; one failure leaves the others running
Two resistors in parallel: Rp = R1R2 / (R1 + R2), the product over the sum. For n equal resistors R in parallel, Rp = R/n.
Series versus Parallel at a Glance
| Feature | Series | Parallel |
|---|---|---|
| Current | Same through each resistor | Divides among branches |
| Potential difference | Divides across resistors | Same across each branch |
| Equivalent resistance | Rs = R1 + R2 + … (larger than any one) | 1/Rp = 1/R1 + 1/R2 + … (smaller than any one) |
| One component fails | Whole circuit stops | Others keep working |
| V-I graph line | Steeper (higher R) | Less steep (lower R) |
| Used in | Ammeter placement, fuse placement, torch cells | Household wiring, all appliances |
Why Household Appliances Are Wired in Parallel
NCERT gives three reasons, and the board expects all three in a 3-mark answer. First, in series the current is the same through every appliance, which is absurd: a bulb needs a small current and a heater a large one. Second, in series the supply voltage divides, so every appliance would get less than 220 V and none would work properly. Third, in series a single failed appliance breaks the circuit for all of them, while in parallel each appliance has its own switch and works independently.
6. Heating Effect of Electric Current
A battery keeps the current flowing by spending its chemical energy. Part of this energy may do useful work (turning a fan), and the rest is dissipated as heat in the resistance of the circuit. In a purely resistive circuit (a heater coil, an iron), all of it appears as heat. This is the heating effect of electric current, also called Joule heating.
Derivation: A current I flows through a resistor R for time t under a potential difference V. Charge that passes is Q = I t. Work done by the source to move this charge is W = V Q = V I t. Power input is P = W/t = V I. This energy is all converted to heat, so H = V I t. Using V = I R:
H = I2 R t
Also, H = V I t and H = V2 t / R, which are the same law in different variables. Choose the form that uses the quantities you are given.
Joule’s law of heating: the heat produced in a resistor is directly proportional to (i) the square of the current, (ii) the resistance, and (iii) the time for which the current flows. Write all three clauses; each carries a mark.
Because H depends on I2, doubling the current makes the heat four times as large for the same R and t. CBSE 2023 turned this into a 1-mark item: if R is halved with the current unchanged, the heat becomes two times. CBSE 2024 asked for the heat in an iron of 20 Ω carrying 5 A for 30 s: H = 25 × 20 × 30 = 15000 J.
Applications of the Heating Effect
- Electric heater, iron, toaster, geyser: the heating element is a nichrome coil. Nichrome has high resistivity (so a short coil gives enough resistance), a high melting point (about 1400 °C) and does not oxidise readily when red hot.
- Electric bulb: the filament must retain as much heat as possible to glow white hot, so it is a thin coiled wire of tungsten, which has a very high melting point (3380 °C) and high resistivity. The bulb is filled with chemically inactive nitrogen and argon to prolong the filament’s life; oxygen would burn it away.
- Electric fuse: a safety device that protects circuits and appliances. It is a short wire of an alloy of aluminium, copper, iron, lead and similar metals, chosen to have the right melting point, and it is placed in series with the live wire of the appliance. When the current exceeds the rated value (because of overloading or a short circuit), the fuse wire heats up, melts, and breaks the circuit. Fuses for domestic use are rated 1 A, 2 A, 3 A, 5 A, 10 A and so on. An iron drawing 1 kW at 220 V takes 4.5 A, so a 5 A fuse suits it.
7. Electric Power and Electrical Energy
Electric power is the rate at which electrical energy is consumed or dissipated in a circuit. From the derivation above, P = W/t = V I.
P = V I = I2 R = V2 / R
The SI unit is the watt (W). The power consumed by a device is 1 watt when a current of 1 ampere flows through it under a potential difference of 1 volt: 1 W = 1 V × 1 A = 1 J/s. CBSE 2025 asked exactly this 2-mark definition. Larger powers are written in kilowatt: 1 kW = 1000 W.
Rated values: a bulb marked 220 V, 100 W is designed to consume 100 W when connected to 220 V. From this you can find its resistance R = V2/P = 2202/100 = 484 Ω and its normal current I = P/V = 100/220 = 0.45 A. If the same bulb is connected to 110 V, its power drops to V2/R = 1102/484 = 25 W, one-fourth, because P ∝ V2 for fixed R.
Electrical Energy and the Commercial Unit
Energy consumed = power × time: E = P t = V I t, measured in joules when P is in watts and t in seconds. The joule is far too small for electricity bills, so the commercial unit is the kilowatt hour (kWh), the energy consumed by a 1 kW device running for 1 hour.
1 kWh = 1000 W × 3600 s = 3.6 × 106 J
One kWh is the “unit” on the electricity bill. Units consumed = (power in kW) × (hours). A 400 W refrigerator running 8 hours a day uses 0.4 × 8 = 3.2 units a day, 96 units in 30 days.
Formula and Reaction Sheet
| Quantity | Formula | SI unit | When to use it |
|---|---|---|---|
| Electric current | I = Q / t | ampere (A) = C/s | Charge and time given |
| Potential difference | V = W / Q | volt (V) = J/C | Work and charge given |
| Ohm’s law | V = I R | - | Any two of V, I, R known; temperature constant |
| Resistance | R = V / I | ohm (Ω) = V/A | Slope of V-I graph |
| Resistance of a wire | R = ρ l / A | ohm (Ω) | Length, area, material given |
| Resistivity | ρ = R A / l | ohm metre (Ω m) | Property of the material |
| Stretched wire (n times length) | R’ = n2 R | ohm (Ω) | Volume constant |
| Wire cut into n parts, all in parallel | R’ = R / n2 | ohm (Ω) | Equal pieces |
| Series combination | Rs = R1 + R2 + R3 | ohm (Ω) | Same current |
| Parallel combination | 1/Rp = 1/R1 + 1/R2 + 1/R3 | ohm (Ω) | Same voltage |
| Two in parallel | Rp = R1 R2 / (R1 + R2) | ohm (Ω) | Product over sum; n equal ones give R/n |
| Heat produced (Joule’s law) | H = I2 R t = V I t = V2 t / R | joule (J) | Time in seconds |
| Electric power | P = V I = I2 R = V2 / R | watt (W) = J/s | I2R for series, V2/R for parallel |
| Electrical energy | E = P t = V I t | joule (J); commercial kWh | Bills: units = kW × hours |
| Commercial unit | 1 kWh = 3.6 × 106 J | - | Cost = units × rate |
Read the rest of the chapter →Hide the rest ↑
Important Definitions
| Term | Definition |
|---|---|
| Electric current | Rate of flow of electric charge through a cross-section of a conductor; I = Q/t; SI unit ampere (A) |
| Potential difference | Work done to move a unit positive charge from one point to another; V = W/Q; SI unit volt (V); 1 V = 1 J/C |
| Ohm’s law | At constant temperature, the current through a conductor is directly proportional to the potential difference across its ends; V = IR |
| Resistance | Property of a conductor that opposes the flow of current through it; R = V/I; SI unit ohm (Ω); 1 Ω = 1 V/A |
| Resistivity | Resistance of a conductor of the material of unit length and unit area of cross-section; ρ = RA/l; SI unit ohm metre (Ω m); depends on material and temperature only |
| Series combination | Resistors joined end to end so the same current flows through each; Rs = R1 + R2 + … |
| Parallel combination | Resistors joined between the same two points so each has the same potential difference; 1/Rp = 1/R1 + 1/R2 + … |
| Heating effect of current | Conversion of electrical energy into heat when current flows through a resistance; H = I2Rt |
| Joule’s law of heating | Heat produced in a resistor is directly proportional to the square of the current, the resistance, and the time of flow |
| Electric power | Rate at which electrical energy is consumed; P = VI; SI unit watt (W) |
| Kilowatt hour | Commercial unit of electrical energy; energy used by a 1 kW device in 1 hour; 1 kWh = 3.6 × 106 J |
| Electric fuse | A safety wire of low melting point placed in series that melts and breaks the circuit when the current exceeds the rated value |
Solved Examples (NCERT-Based)
Example 1: Length of a copper wire for a given resistance
A copper wire has diameter 0.5 mm and resistivity 1.6 × 10-8 Ω m. What length of this wire would make its resistance 10 Ω? How much does the resistance change if the diameter is doubled?
Solution: r = 0.25 mm = 0.25 × 10-3 m. A = π r2 = 3.14 × (0.25 × 10-3)2 = 1.96 × 10-7 m2.
l = R A / ρ = 10 × 1.96 × 10-7 / (1.6 × 10-8) = 122.7 m (about 123 m).
Doubling the diameter makes the area 4 times, so the resistance falls to one-fourth: 10/4 = 2.5 Ω.
Example 2: Board numerical on resistivity (CBSE 2025)
The resistance of a wire of 0.01 cm radius is 14 Ω. If the resistivity of the material of the wire is 44 × 10-8 Ω m, find the length of the wire. (Take π = 22/7.)
Solution: r = 0.01 cm = 1 × 10-4 m. A = π r2 = (22/7) × 10-8 m2.
l = R A / ρ = 14 × (22/7) × 10-8 / (44 × 10-8) = 44 × 10-8 / (44 × 10-8) = 1 m.
The examiner set the numbers so that the answer is clean. If your answer to a board numerical is an ugly decimal, recheck the unit conversion of the radius first.
Example 3: Parallel resistors and total current
Three resistors of 5 Ω, 10 Ω and 30 Ω are connected in parallel to a 12 V battery. Find the current through each resistor, the total current, and the equivalent resistance.
Solution: Each resistor has 12 V across it. I1 = 12/5 = 2.4 A; I2 = 12/10 = 1.2 A; I3 = 12/30 = 0.4 A.
Total current I = 2.4 + 1.2 + 0.4 = 4 A. Equivalent resistance Rp = V/I = 12/4 = 3 Ω.
Check: 1/Rp = 1/5 + 1/10 + 1/30 = 10/30, so Rp = 3 Ω, below the smallest branch as it must be.
Example 4: Same three resistors, series and parallel (CBSE 2025)
Three resistors of 2 Ω, 3 Ω and 6 Ω are connected in (i) series and (ii) parallel. Find the equivalent resistance of each arrangement.
Solution: (i) Series: Rs = 2 + 3 + 6 = 11 Ω.
(ii) Parallel: 1/Rp = 1/2 + 1/3 + 1/6 = (3 + 2 + 1)/6 = 1, so Rp = 1 Ω.
The 3-mark version also asks you to draw both arrangements: three rectangles in one line for series, three rectangles stacked between two common junctions for parallel.
Example 5: Potential difference from heat (NCERT Example 11.7)
100 J of heat is produced each second in a 4 Ω resistance. Find the potential difference across the resistor.
Solution: H = I2 R t, so 100 = I2 × 4 × 1, I2 = 25, I = 5 A. Then V = I R = 5 × 4 = 20 V.
Example 6: Iron at maximum and minimum heating (NCERT Example 11.8)
An electric iron consumes energy at a rate of 840 W when heating is at the maximum rate and 360 W at the minimum. The voltage is 220 V. Find the current and resistance in each case.
Solution: Maximum: I = P/V = 840/220 = 3.82 A; R = V/I = 220/3.82 = 57.60 Ω.
Minimum: I = 360/220 = 1.64 A; R = 220/1.64 = 134.15 Ω.
A lower heat setting means a higher resistance in the circuit and a smaller current; the iron switches in a longer section of its element.
Example 7: Power in the same resistor in two circuits (NCERT Exercise)
Compare the power used in the 2 Ω resistor in each of the following circuits: (i) a 6 V battery in series with 1 Ω and 2 Ω resistors, and (ii) a 4 V battery in parallel with 12 Ω and 2 Ω resistors.
Solution: (i) Total R = 3 Ω, I = 6/3 = 2 A through both resistors. P = I2R = 22 × 2 = 8 W.
(ii) The 2 Ω resistor has the full 4 V across it. P = V2/R = 16/2 = 8 W.
The power is the same in both cases, 8 W. The 12 Ω resistor in circuit (ii) is a distraction; in parallel it has no effect on the 2 Ω branch.
Competency-Based Questions (with answers)
1. Case-based: The kitchen circuit
Riya’s kitchen has a 2000 W heater and a 100 W bulb, both rated for 220 V, connected in parallel to the mains. The heater has a resistance of about 25 Ω and the bulb about 500 Ω. Both are switched on together.
(a) Which device carries the larger current, and how much? The heater: I = V/R = 220/25 = 8.8 A. The bulb carries 220/500 = 0.44 A. The lower resistance draws the larger current at the same voltage.
(b) What is the total current drawn from the mains? In parallel, currents add: 8.8 + 0.44 = 9.24 A. A 10 A fuse would be suitable for this pair; a 5 A fuse would blow.
(c) If the two were mistakenly connected in series across 220 V, which would glow more brightly? Series current I = 220/(25 + 500) = 0.42 A through both. Power in the bulb = I2R = 0.422 × 500 = 88 W (near its rating); in the heater = 0.422 × 25 = 4.4 W. The bulb would glow, the heater would stay almost cold. In series the larger resistance takes the larger share of power.
2. Case-based: Reading the electricity bill
A family’s bill shows 240 units for the month of June. Their appliances include a 1.5 kW air conditioner used 4 hours daily, a 100 W television used 5 hours daily, and four 10 W LED bulbs used 6 hours daily. The tariff is Rs 6 per unit.
(a) How many units does the air conditioner consume in June (30 days)? 1.5 kW × 4 h × 30 = 180 kWh = 180 units.
(b) How many units do the television and the bulbs together consume? TV: 0.1 kW × 5 × 30 = 15 units. Bulbs: 4 × 0.01 kW × 6 × 30 = 7.2 units. Total 22.2 units.
(c) The remaining units are used by a refrigerator. What is the refrigerator’s share of the bill in rupees, and what is the energy it used in joules? Refrigerator units = 240 - 180 - 22.2 = 37.8 units. Cost = 37.8 × 6 = Rs 226.80. Energy = 37.8 × 3.6 × 106 = 1.36 × 108 J.
3. Source-based: A student’s V-I data (CBSE 2024)
A student records the current I through a resistor for different potential differences V across it: I = 0.5, 1.0, 2.0, 3.0, 3.5 A against V = 1.5, 3.0, 6.2, 9.3, 10.8 V.
(a) What kind of graph do you get when V is plotted against I? A straight line passing through the origin.
(b) Find the resistance of the resistor from the data. V/I for each pair: 3.0, 3.0, 3.1, 3.1, 3.09 Ω. The slope of the V-I line is about 3.1 Ω, so R is approximately 3 Ω.
(c) Why should the graph pass through the origin? When the potential difference is zero, no current flows. Ohm’s law V = IR gives V = 0 at I = 0, so the line must pass through (0, 0).
4. Assertion-Reason
Assertion (A): The bending of a wire in the form of a coil of several turns does not affect its electrical resistance. Reason (R): The electrical resistance of a wire is directly proportional to its electrical resistivity.
Answer: (b) Both A and R are true, but R is not the correct explanation of A. Bending leaves length, area and material unchanged, which is why R stays the same; the proportionality to resistivity is true on its own but does not explain the assertion. (CBSE 2025)
5. Assertion-Reason
Assertion (A): Alloys are used in the heating elements of electric irons and toasters. Reason (R): Alloys have higher resistivity than their constituent metals and do not oxidise readily at high temperatures.
Answer: (a) Both A and R are true, and R is the correct explanation of A. High resistivity gives the needed resistance in a compact coil; resistance to oxidation lets the coil stay red hot for years.
6. Assertion-Reason
Assertion (A): A voltmeter is connected in parallel across the component whose potential difference is to be measured. Reason (R): A voltmeter has a very low resistance.
Answer: (c) A is true, R is false. A voltmeter has a very high resistance so that it draws negligible current from the branch it is measuring. The low-resistance instrument is the ammeter.
7. Data reasoning: Two LED bulbs in series (CBSE 2023)
Two LED bulbs of 12 W and 6 W are connected in series. The current through the 12 W bulb is 0.06 A. What is the current through the 6 W bulb?
Answer: 0.06 A. In a series circuit the same current flows through every component, regardless of their power ratings. The ratings only tell you that the two bulbs will share the supply voltage unequally.
8. Competency MCQ: Combinations giving 1 Ω (CBSE 2024 pattern)
Which of these combinations has an equivalent resistance of exactly 1 Ω: (I) two 2 Ω resistors in parallel; (II) three 3 Ω resistors in parallel; (III) a 2 Ω and a 3 Ω resistor in parallel; (IV) 0.5 Ω and 0.5 Ω in series?
Answer: I, II and IV. (I) 2/2 = 1 Ω. (II) 3/3 = 1 Ω. (III) 2 × 3/(2 + 3) = 1.2 Ω. (IV) 0.5 + 0.5 = 1 Ω. For n equal resistors in parallel the quickest route is R/n.
Important Questions for Board Exams
1-Mark Questions
- State Ohm’s law. At constant temperature, the current through a conductor is directly proportional to the potential difference across its ends: V = IR.
- Define one volt. The potential difference between two points is 1 volt when 1 joule of work is done to move a charge of 1 coulomb between them.
- Why is an ammeter connected in series? So that the entire current of the circuit passes through it; it has a low resistance so it does not reduce that current.
- Express 1 kWh in joules. 1 kWh = 3.6 × 106 J.
2-Mark Questions
- Calculate the resistance of a copper wire of length 1000 m and area of cross-section 2 mm2. Resistivity of copper is 1.6 × 10-8 Ω m. (CBSE 2024) A = 2 mm2 = 2 × 10-6 m2. R = ρl/A = 1.6 × 10-8 × 1000 / (2 × 10-6) = 8 Ω.
- Define electric power. When do we say that the power consumed in a circuit is 1 watt? (CBSE 2025) Electric power is the rate at which electrical energy is consumed, P = VI. The power is 1 watt when a current of 1 ampere flows under a potential difference of 1 volt.
3-Mark Questions
- State Joule’s law of heating. A coil of resistance 50 Ω carries 2 A for 30 s. Find the heat produced. Heat is proportional to I2, to R and to t. H = I2Rt = 4 × 50 × 30 = 6000 J.
- Write the relation between resistance and resistivity for a cylindrical conductor of length l and area A. Derive the SI unit of resistivity. Why are alloys used in electrical heating devices? (CBSE 2025) R = ρl/A, so ρ = RA/l; unit = Ω × m2/m = Ω m. Alloys have higher resistivity than pure metals and do not oxidise or burn readily at high temperature.
5-Mark Questions
- (i) How is the current through a conductor related to the potential difference across it? Draw a labelled circuit diagram to verify this relationship. (ii) Why should an ammeter have low resistance? (iii) Two V-I graphs A and B are drawn for the series and parallel combinations of the same two resistors. Which is which, and why? (CBSE 2023) (i) Directly proportional at constant temperature, V = IR; diagram with battery, key, ammeter and nichrome wire in series, voltmeter across the wire. (ii) So that it does not change the current it is meant to measure. (iii) The steeper V-I line has the larger resistance, so it is the series combination; the less steep line is the parallel combination.
Common Mistakes and Examiner Tips
- Stating Ohm’s law without the condition. “V is proportional to I” earns partial credit only. Add “provided the temperature and other physical conditions remain constant”.
- Confusing resistance with resistivity. Cutting, stretching or thickening a wire changes R; only changing the material or its temperature changes ρ. If a question says “resistivity of a wire depends on its length”, the statement is false.
- Leaving area in mm2. 1 mm2 = 10-6 m2, and 1 cm = 10-2 m, so a radius of 0.01 cm is 10-4 m and its square is 10-8 m2. Most wrong answers in resistivity numericals trace back to this step.
- Adding resistances in parallel like series. Add reciprocals, then invert. Sanity check: a parallel result must be smaller than the smallest branch. If your parallel answer is larger than any branch, the arithmetic is wrong.
- Applying the stretched-wire result to a cut wire. Stretching to n times length multiplies R by n2. Cutting into n pieces divides R by n per piece; joining those pieces in parallel divides by n2.
- Using P = V2/R with the wrong V. A bulb rated 220 V, 100 W has R = 484 Ω always; on 110 V it consumes 1102/484 = 25 W. Students often write 50 W (halving) instead of 25 W (quartering).
- Picking the wrong power formula for “which glows brighter”. Series: same I, so use I2R, higher R glows brighter. Parallel: same V, so use V2/R, lower R glows brighter. The bulb with the higher wattage rating is the brighter one only when both get their rated voltage, which is the parallel case.
- Mixing joules and kilowatt hours. Bill questions: keep power in kW and time in hours; the product is already in units. Convert to joules only if the question asks, using 1 kWh = 3.6 × 106 J.
- Time in minutes or hours inside H = I2Rt. t must be in seconds for the answer to come out in joules. 30 minutes is 1800 s.
- Circuit diagram slips. Voltmeter in series, ammeter in parallel, battery lines of equal length, no key, or the voltmeter drawn across the battery instead of across the resistor. Each of these costs the diagram mark in a 3-mark or 5-mark question.
- Giving only one reason for parallel wiring at home. The marking scheme looks for three: each appliance gets the full 220 V, each can be switched independently, and each can draw a different current. Write all three.
Quick Revision Points
- Current I = Q/t, unit ampere; 1 A = 1 C/s; 1 C = charge on about 6 × 1018 electrons
- Potential difference V = W/Q, unit volt; 1 V = 1 J/C
- Ohm’s law: V = IR at constant temperature; V-I graph a straight line through the origin; slope of V-I graph = R
- Resistance R = V/I, unit ohm; 1 Ω = 1 V/A
- R = ρl/A: R ∝ l, R ∝ 1/A, depends on material; R rises with temperature for metals
- Resistivity ρ = RA/l, unit Ω m; depends only on material and temperature
- Stretch to n times length: R becomes n2R; cut into n pieces in parallel: R/n2; double the diameter: R/4
- Series: Rs = R1 + R2 + …; same current; voltage divides; larger than largest
- Parallel: 1/Rp = 1/R1 + 1/R2 + …; same voltage; current divides; smaller than smallest; two in parallel = product/sum
- Heating effect: H = I2Rt = VIt = V2t/R; Joule’s law has three clauses
- Nichrome for heating elements; tungsten (melting point 3380 °C) for filaments; fuse wire in series with the live wire
- Power P = VI = I2R = V2/R, unit watt; 1 W = 1 J/s; rating gives R = V2/P
- Energy E = Pt; 1 kWh = 1 unit = 3.6 × 106 J; units = kW × hours
Weightage in Board Exams
Electricity sits in Unit IV, Effects of Current, which CBSE allots 13 marks together with Chapter 12, Magnetic Effects of Electric Current. In practice Electricity takes the larger share, typically 6 to 8 marks, because it supplies the physics numericals. From 2026 the paper is arranged by discipline: Section C (Physics) carries 25 marks across Chapters 9 to 12, with 6 MCQs, a 2-mark very short answer, two 3-mark questions, one 5-mark question and one 4-mark case-based question.
| Question type | Marks | What Electricity contributes (from 2023 to 2025 papers) |
|---|---|---|
| MCQ | 1 each | Heat when R is halved (2023); current in series LED bulbs (2023); heat in a 20 Ω iron at 5 A for 30 s (2024); combinations giving 1 Ω (2024) |
| Assertion-Reason | 1 | Bending a wire and its resistance (2025); electron flow and potential (2024) |
| Very short answer | 2 | Copper wire 1000 m, 2 mm2 (2024); wire cut into three parallel parts, or define electric power and 1 watt (2025) |
| Short answer | 3 | Series and parallel of 2, 3, 6 Ω; resistivity unit derivation and alloys; define one ampere plus a resistivity numerical (all 2025) |
| Long answer | 5 | Ohm’s law verification circuit, ammeter resistance, series versus parallel V-I graphs (2023); 2000 W heater versus 100 W bulb, or plotting V-I data (2024) |
| Case-based | 4 | Circuit with a 16 Ω resistor and two 8 Ω in parallel: total resistance, current, potential difference (2024) |
The pattern is stable: one or two 1-mark items, one numerical on resistivity or combinations, and one long question that mixes a circuit diagram with a calculation.
Class 10 Science · Chapter 11 – swipe through all 10 cards to understand the whole chapter.
Current and Charge
Current is the rate at which charge flows past a point in a conductor.
Conventional current runs + to −; electrons move the other way.
- Measured with an ammeter connected in series, low resistance.
- 0.5 A for 10 min moves Q = 0.5 × 600 = 300 C.
- No closed path, no current: open the key and the whole loop stops.
Potential Difference
The work done to move a unit positive charge from one point to another.
Measured with a voltmeter connected in parallel, high resistance.
- 100 J to move 20 C means V = 5 V.
- A cell keeps the potential difference steady using its chemical energy.
- Potential difference is the cause; current is the effect.
Ohm’s Law
At constant temperature, current is directly proportional to the potential difference.
Always state the condition: temperature and physical conditions constant.
- V-I graph of an ohmic conductor: straight line through the origin, slope = R.
- Steeper V-I line = larger resistance (series beats parallel).
- A bulb filament is non-ohmic: R rises as it heats, the graph bends.
Resistance of a Wire
Longer and thinner wires resist more; the material sets the scale.
Unit of ρ is Ω m; 1 mm2 = 10⁻6 m2.
- Resistivity depends only on material and temperature, never on length or area.
- Copper wire, 1000 m, 2 mm2, ρ = 1.6 × 10⁻8 Ω m gives R = 8 Ω.
- Alloys (nichrome, constantan) have higher ρ than their metals.
Stretch, Cut, Bend
Change the shape of a wire and its resistance changes in a fixed pattern.
Bending into a coil changes nothing (CBSE 2025 assertion-reason).
- 10 Ω stretched to double length becomes 40 Ω.
- R cut into three equal parts in parallel gives R/9.
- Doubling the diameter quarters the resistance (area goes as r2).
Series and Parallel
Series shares the voltage; parallel shares the current.
Series result is above the largest; parallel result is below the smallest.
- 2 Ω, 3 Ω, 6 Ω: series 11 Ω, parallel 1 Ω.
- Two in parallel: product over sum; n equal ones: R/n.
- Homes are wired in parallel: full 220 V, independent switches, own current.
Heating Effect
Electrical work done against resistance turns into heat.
Heat ∝ I2, ∝ R, ∝ t; time must be in seconds.
- 20 Ω iron at 5 A for 30 s: H = 25 × 20 × 30 = 15000 J (CBSE 2024).
- Halve R with the same current and the heat halves (CBSE 2023).
- Fuse wire: low melting point alloy, in series, melts on overload.
Nichrome, Tungsten, Fuse
Each heating application picks a material for its resistivity and melting point.
Bulbs are filled with argon and nitrogen so the filament does not burn.
- Nichrome: high ρ, high melting point, no oxidation, so heaters and irons.
- Tungsten: melting point 3380 °C, so it can glow white hot as a filament.
- Fuse ratings 1 A, 2 A, 3 A, 5 A, 10 A; a 1 kW iron at 220 V needs 5 A.
Electric Power
The rate at which electrical energy is consumed.
1 W = 1 J/s = 1 V × 1 A; rating gives R = V2/P.
- 220 V, 100 W bulb has R = 484 Ω; on 110 V it uses only 25 W.
- Series: same I, use I2R, higher R glows brighter.
- Parallel: same V, use V2/R, lower R glows brighter.
Energy and the kWh
Energy is power times time; the bill counts it in units.
Units = kW × hours; convert to joules only if asked.
- 400 W fridge, 8 h/day, 30 days: 0.4 × 8 × 30 = 96 units.
- At Rs 3 per unit that costs Rs 288 (NCERT Example 11.10).
- 1.5 kW geyser, 2 h/day for 30 days: 90 units.
📝 Practice Electricity - 10 board questions
CBSE previous-year and competency-based · with answers & explanations
Start →Close ✕
Chapter Navigation
Previous: Human Eye and Colourful World Class 10 Notes
Next: Magnetic Effects of Electric Current Class 10 Notes
Related Chapters in Class 10 Science
- Magnetic Effects of Electric Current Class 10 Notes
- Light Reflection and Refraction Class 10 Notes
- Human Eye and Colourful World Class 10 Notes
Practice What You Learned
Test yourself with our Class 10 Science Mock Papers to see how well you’ve mastered the concepts.
Explore More
Frequently Asked Questions
Current is the rate of flow of charge through a conductor, I = Q/t, measured in amperes. Potential difference is the work done to move a unit charge between two points, V = W/Q, measured in volts. Potential difference is the cause and current is the effect: a cell sets up the potential difference and the current follows.
An ammeter measures the current through a component, so it must sit in the same path (series) and have very low resistance so it does not reduce that current. A voltmeter measures the potential difference across a component, so it is connected across it (parallel) and has very high resistance so it draws almost no current.
Resistance is directly proportional to the length of the conductor, inversely proportional to its area of cross-section, and depends on the material through its resistivity. For metals it also increases with temperature. All of this is captured in R = ρl/A, where ρ depends only on the material and its temperature.
In parallel every appliance gets the full 220 V supply, each can draw the different current it needs, and each can be switched on or off on its own. If one appliance fails the rest keep working. In series the voltage would divide, all appliances would carry the same current, and one failure would switch off everything.
One unit is one kilowatt hour (kWh), the energy used by a 1000 W appliance running for one hour. It equals 3.6 × 10⁶ joules. Units on a bill are found by multiplying power in kilowatts by time in hours; a 400 W refrigerator running 8 hours a day uses 3.2 units a day.
Electricity shares Unit IV, Effects of Current, with Magnetic Effects for a combined 13 marks, and usually takes 6 to 8 of them. Recent papers have asked a 1-mark question on Joule heating, a 2-mark resistivity numerical, a 3-mark series and parallel calculation, and a 5-mark Ohm’s law circuit with V-I graphs.
Resistance is the opposition offered by a particular piece of conductor; it depends on length, area, material and temperature and is measured in ohms. Resistivity is a property of the material alone at a given temperature, equal to the resistance of a piece of unit length and unit area, and is measured in ohm metres. Cutting or stretching a wire changes its resistance and leaves its resistivity unchanged.
Nichrome has a high resistivity, a high melting point and does not oxidise easily when red hot, so a compact coil of it produces a lot of heat safely for years. Tungsten has an even higher melting point, about 3380 °C, so a thin filament can be heated white hot to give light without melting; the bulb is filled with argon and nitrogen to stop the filament burning away.
very nice notes they all chapter notes are use full for boad exam
thank you
for notes
Thank you hitesh, glad the notes are helping for your boards.